Famco Fireplace Services Nationwide

Famco Fireplace Services in Atlanta: What to Know First

We provide independent Famco fireplace services across Atlanta, from gas fireplace tune-ups in Buckhead to damper repairs in Decatur and firebox rebuilds in Virginia-Highland. Most Famco jobs are diagnosed, quoted in writing, and completed within a single visit - two if we need to source a specific part. You’ll get our written price before any work starts, every time, no exceptions.

Call (470) 435-7984

This page is for Atlanta homeowners who own a Famco gas fireplace, wood-burning unit, or insert and need service that doesn’t require calling the manufacturer or hoping a general handyman recognizes the venting configuration. If your Famco unit is showing error codes, drafting poorly, or hasn’t been serviced since you bought the place, we can inspect it, document what we find, and give you a firm number to fix it. Call (470) 435-7984 for a free estimate.

How Famco Products Fail - and How We Fix Them

• Famco FV36 direct-vent gas fireplaces - failed ignition modules in Atlanta’s humidity. The FV36’s SIT 820 Nova ignition module sits in a compartment that traps moisture during Georgia’s July-through-September muggy stretches. We’ve replaced dozens in Midtown condos where the unit clicks but never lights, or lights and drops out after thirty seconds. Our fix: pull the module, test spark and thermopile output, install a new OEM SIT module or a Robertshaw equivalent if the customer prefers, and reseal the compartment with silicone rated for 400°F.
• Famco wood-burning inserts - cracked refractory panels from thermal cycling. Atlanta’s temperature swings, especially in older homes with poor insulation, stress the refractory panels in Famco insert fireboxes. The cracks start hairline and widen after a season of heating from 40°F mornings to 600°F burns. We measure every crack against NFPA 211 standards: anything over 1/8 inch or penetrating the full thickness means replacement. We source Famco-spec refractory or HeatShield panel systems when the OEM part is back-ordered.
• Famco chimney-top dampers - seized cables after pollen season. The Famco Sealtight damper uses a stainless cable that runs down the flue to a handle at the firebox. In Atlanta, oak pollen and pine needle debris bind the cable guide every spring. Homeowners in Druid Hills and Morningside call us in October when the damper won’t open for first fire. We don’t just free the cable; we pull the assembly, clean the guide track, lubricate with high-temp graphite, and test ten full cycles before we sign off.
• Famco gas log sets - deteriorating ember beds and faded ceramic fiber. The glowing ember material in Famco vented gas log sets breaks down after 4-6 years of regular use, especially in homes that run the pilot continuously. The fix looks simple but isn’t: replace with OEM Famco ember material or Gelco ceramic fiber that matches the BTU rating and flame pattern. Wrong material and the logs soot, the flame turns lazy, and you get an incomplete combustion smell in the room.
• Famco flex liners - condensation corrosion in exterior chase chimneys. Famco’s flexible aluminum liners, common in 1980s and 1990s Atlanta construction, corrode from the outside in when installed in exterior masonry chases. The chase stays colder than the flue gas, moisture condenses on the liner wall, and the aluminum pits through in sections. We camera-scan the full length, mark the damaged footage, and replace with DuraFlex stainless or Olympia Chimney’s AL29-4C alloy if it’s a high-efficiency gas appliance. The camera doesn’t negotiate - it just shows you what’s there.

Our Famco Fireplace Services Process

1. 1
   Call and schedule. A live person answers, checks our calendar, and books your appointment. You’ll get a text when your tech is en route.
2. 2
   NFPA 211 Level 2 inspection with camera. We run a chimney camera down the flue, inspect the firebox, smoke chamber, and exterior termination. Every image is saved to your job record under Haven Standard Clause 4.
3. 3
   Written diagnosis and price. Before any work, you get a written scope, written price, and written warranty. Clause 1 of the Haven Standard: have it in writing. No surprises, no “we found something else” after we’re halfway in.
4. 4
   Parts decision - OEM or quality aftermarket. We stock common Famco parts and source through our Haven buying network. If Famco OEM is back-ordered, we’ll quote a DuraFlex, HeatShield, or Gelco equivalent that meets or exceeds spec, with your approval.
5. 5
   Repair, test, and document. We complete the work, run combustion analysis on gas units, do a smoke test on wood units, and photograph the finished condition. Your documented record is delivered by email.
6. 6
   365-Day Done Right Promise. If it’s not done right, we make it right. The promise is stamped on every job, Famco or otherwise.

Before

After

What Famco Fireplace Services Costs in Atlanta

These are Atlanta market ranges based on jobs we’ve completed in Fulton, DeKalb, and Cobb counties. Your exact price comes after inspection, never before. Estimates are free - call (470) 435-7984.

Why Atlanta Homeowners Call Level Two Chimney Atlanta for Famco Work

We’ve been running camera-down inspections in Atlanta since 2009, and Corrine Halstead and her crew have handled Famco products in enough Inman Park Craftsman renovations and Virginia-Highland flips to know which parts fail first and which substitutes hold up. Every technician is background-checked, uniformed, and arrives with a license number you can verify. We don’t sell - we document, price, and let you decide. If you’ve got a competitor’s written estimate, we’ll give you a free second opinion. And because we buy through the Haven network across DuraFlex, HeatShield, Gelco, Olympia Chimney, and Copperfield, we’re not locked to one supplier’s pricing or availability.

FAQs